
While your Lennox® heating system cannot talk to you, it possesses a way to tell you about a furnace error.
Its control panel has two LED lights that can display a fault code. Subject to the fault, your heating system may show continuous or flashing lights.
While there are some elementary HVAC fixes you can complete on your own, the majority of fixes are best left to HVAC technicians. When your heater will not turn on or give warmth, get in touch with Interstate Heating & Air Conditioning at 402-509-5940 for expert furnace repair in Omaha.
Our specialists will swiftly detect and take care of the problem, even if you don’t have a Lennox heater. We can fix all kinds or models—and get the comfort reintroduced to your house without delay.
What Does the Flashing Light on My Heater Mean?
Your heater relies on lights to flash code when it is malfunctioning. It also uses this setup to let you know it’s operating like it should.
Normal heating consists of:
- Concurrent slow flash—heating system operating correctly.
- Simultaneous fast flash—heater is starting to call for heat.
If you notice a solitary light going on and off slowly and the other blinking quickly, your furnace could be experiencing a low flame signal. This can happen even when your furnace is working like it should. It indicates the flame sensing rod may need to be cleaned or in the wrong area on the burner. Reach out to us at 402-509-5940 for assistance.
Here are some of the most typical problems for Lennox heaters.
Furnace Refuses to Kick On
Here are some of the light patterns you could notice when your heating system refuses to or keep running. The bulk of these issues must be fixed by a professional, such as one from Interstate Heating & Air Conditioning.
- The duo of LED lights are off. This signifies your HVAC system might not have electricity. Examine the breaker box to confirm the heating system fuse has not flipped. Attempt to reset the fuse if it is in the “off” spot. If it immediately turns off following a reset, don’t touch the breaker and contact us at 402-509-5940.
- A single light is continuous and the other is flickering slowly. This implies the flame rollout switch is possibly open. The part is a critical safety device that aids in avoiding fires and carbon monoxide. You shouldn’t try to handle this malfunction without professional help.
- A single light is blinking fast and the other is blinking slowly. This likely indicates power polarity has been transposed. Your heating system may have a wiring problem that needs expert assistance from Interstate Heating & Air Conditioning.
- The duo of lights are blinking slowly. This means your heater’s blower motor probably isn’t operating. This piece circulates warm air from the heater into your space. We can assist in figuring out what’s causing an issue with this part.
- A single light is blinking slowly and the other is flashing rapidly. This means your heater may have not enough voltage or a short circuit. Contact our technicians at 402-509-5940 for assistance.
- One light is flashing on, on, off while the other blinks on, off, on. This means there could be trouble with your heating system’s motherboard or wiring. Interstate Heating & Air Conditioning can determine the fault and fix it.
- The pair of lights display every other slow flickers. This signifies your HVAC equipment likely has a flame issue. There may be a problem with its gas supply, gas valve or ignitor control. Call us at 402-509-5940 for help.
- A single light flashes slowly while the other is continuous. This typically indicates your heating system’s limit switch is malfunctioning. The switch stops your HVAC equipment from getting too hot. Call the specialists at Interstate Heating & Air Conditioning for support.
Heater Blower Operates But No Heat
Here’s what could be at fault when you hear your heater’s blower fan running, but you aren’t gaining any warmth.
- The pair of lights are showing every other fast flickers. This means your furnace ignitor could be broken. This part ignites gas in your furnace to produce warm air and should be fixed by a technician from Interstate Heating & Air Conditioning.
Trust Us for Expert Furnace Repair
When you need to get your heating system repaired fast, trust the technicians at Interstate Heating & Air Conditioning. Our pros will fix the error quickly and have your house feeling relaxing again in no time. Reach out to us at 402-509-5940 or contact us online to get an appointment now.